GSS Grundig SAT Systems GmbHBeuthener Straße 43D-90471 NurembergPhone: +49 (0) 911 / 703 8877Fax: +49 (0) 911 / 703 9210E-mail: [email protected]:
- 10 -- 10 -4 The control panel at a glance4.1 Menu itemsProgram the cassette using the buttons on the control unit of the head-end station. The two-
- 11 -- 11 -5 Programming5.1 Preparation• Connect the test receiver to the HF output or the test output of the head-end station.• Set the output chann
- 12 -- 12 -5.3 Programming procedureEin / OnBE–Remoteplease wait …V 37Box 4C2-69,S2-41 QPSK-PAL– – –Bx 1AC5-12,S3-24TWIN-SATC07Bx 1AC5-12,S3-24TWIN-S
- 13 -- 13 -Bx 4ATeletext:OUTPUT:onon / offBx 4ATXT-Page:SUBTITLE:150Bx 4ATXT-Norm:SUBTITLE:WestBx 4ADual normalAUDIO-OUT:normal / swapMPEG / VPSWest
- 14 -- 14 -Bx 4A 01/10+Das ErsteTVBx 4ASR= 27500INPUT:Bx 4A01/02 AUDIO-IN:“deu” Bx 4AVolume:AUDIO-OUT:0 dBBx 4AARDPROVIDER:–24 … +6Bx 4A13:48:22
- 15 -- 15 -5.3.1 Decoding 2 stations with one CA module (channel strip “B”)Bx 4BS09OUTPUT:Bx 4Bf = 10600 MHzLNB-FREQ:Bx 4BSR= 22000INPUT:▶ ◀/Bx 4Bf
- 16 -- 16 -5.3.2 Time controlled switchingBx 4aDas Erste QPSK-PALS21Bx 4aOn Time TIMER:20:00Bx 4bZDF QPSK-PALS09 ▶ ◀/Bx 4aOff Time TIMER:23:00▶ ◀/Bx
- 17 -- 17 -5.4 Programming the cassette —> Pressing the button for longer than 2 seconds cancels the pro-gramming procedure. This takes you back
- 18 -- 18 -5.4.1 Programming the main menu of the cassetteQuerying the software version—> The display shows e.g. the menu “Bx 4A QPSK-PAL”: “
- 19 -- 19 -• By pressing , select channel strip “A” / “B” or “a” / “b”.—> The capital letters “A” and “B” indicate the channel strips of the ma
- 2 -- 2 -Contents1 Safety regulations ...42 General
- 20 -- 20 -• Press the button.—> The “Setting the TV standard of the output signal” – “NORM” menu is activated.Setting the TV standard of the o
- 21 -- 21 -Setting the fine-tuningOnly change the fine-tuning in exceptional circumstances, since once you change it, all connected television sets o
- 22 -- 22 -• Press the button.—> The “Setting the input symbol rate” – “INPUT: ”and e.g. “SR=27500” menu is activated.Setting the input symbol
- 23 -- 23 -of the antenna system and head-end station as well as the preceding settings of the cassette. • Use ▶ ◀ / to position the cursor under th
- 24 -- 24 -Channel selectionAs soon as the automatic station search has found all of the TV or radio channels, the corresponding data appears in the
- 25 -- 25 -• To select the TV and radio stations of this broadcaster, use the buttons.• By pressing , you can call up various station information
- 26 -- 26 -Setting the volume levelIn this menu, you can balance unequal volume levels of TV and radio stations in the various channel strips.• Set t
- 27 -- 27 -Example: Summertime support for the time zone of Germany (GMT + 1 hour) is in: If “S” is switched on, one hour is added in addition to off
- 28 -- 28 -5.4.1.1 Adjusting the output levels of the channel stripsIn this menu you can set the output levels of the modulators of the channel stri
- 29 -- 29 -5.4.1.2 Settings for TV stationsThe following settings “Automatic picture format conversion”, “Teletext mode” and “Teletext subtitle page
- 3 -- 3 -5.4.1.1 Adjusting the output levels of the channel strips ...285.4.1.2 Settings for TV stations ...
- 30 -- 30 -Adjusting the picture formatIf problems with the automatic picture format switchover (e.g. 4:3, 16:9, Letterbox) arise with the connected
- 31 -- 31 -Switching teletext mode off/onIn this menu you can define whether the teletext of the chan-nel set is transmitted or not.• By pressing t
- 32 -- 32 -Setting the teletext standardIn this menu you define the characters to display the languag-es. For the Western European languages set “Wes
- 33 -- 33 -Setting the audio modeIn this menu you can define whether the Mono, Stereo or Dual Tone signal from the MPEG data stream or the VPS Sig-na
- 34 -- 34 -5.4.2 Decoding 2 stations with one CA module – This feature is only possible via channel strip “B”. – The settings not described bel
- 35 -- 35 -Selecting the channel strip• Select channel strip “B” (page 18).Modulator operating mode—> Setting see page 19.Setting the TV standard
- 36 -- 36 -Switching on decoding / Setting the input symbol rateThe input symbol rate is not to be set if decoding is activated.—> Setting the in
- 37 -- 37 -Switch off decoding • Press the button.—> The display shows “INPUT: and e.g. SR= 22000”. Continue with “Setting the input symbol rat
- 38 -- 38 -5.4.3 Setting time-controlled, alternative channelsChannels can be switched on and off by means of a timer in this menu. Here, for the se
- 39 -- 39 -Setting the switch-off time • Use ▶ ◀ / to position the cursor under the digit (hours / minutes) to be set. • Press to set the desired
- 4 -- 4 -1 Safety regulations Warning• Assembly, installation and servicing should be carried out by authorised electricians.• Switch off the operati
6 Channel and frequency tablesCCIR – Band I/III (Frequency raster 7 MHz)CCIR – Hyperband (Frequency raster 8 MHz)CCIR – Band IV/V (Frequency raster 8
- 5 -- 5 -2.2 Meaning of the symbols used Important note—> General note• Performing works2.3 Technical dataThe devices meet the following
- 6 -- 6 -ConnectionsSAT inputs A and B: 2 F socketsHF output (modulators): 1 IEC socketConnection strip (10-pin): for supply voltages and control
- 7 -- 7 -2.5 Software queryControl unitIf necessary, you can activate the indication of the software version of the con-trol unit manually: • Press a
- 8 -- 8 -3.2 Installing the F terminals To comply with the current EMC regulations, it is necessary to connect the lines leading in and out of the
- 9 -- 9 -Notes: 3 Slot for CA module4 Eject button for CA module5 Socket “RS 232” The operating software of the cassette can be updated via the
Comments to this Manuals